Home :: Lignatool Woodworking Systems :: Lignatool Dovetail Mortise & Tenon Template

Lignatool Dovetail Mortise & Tenon Template

Dovetail mortise and tenon template

 

 

Make accurate, tight-fitting dovetails with a heavy-duty router.

Dovetail mortise and tenon in detail

A safe, solid, well-designed tool! 

FAST. 

Cut a mortise and tenon in minutes! (See video below.)

SMART.

Make compound angles and strong connections with ease. Inch Scales and Block or Sliding fences FOR EASY SET-UP, WITH EVERY SYSTEM 

SAFE. 

Router locks securely onto the guide plate, preventing kick-back if you hit a knot.

MORE Safety: TOP-MOUNTED DUST DEFLECTOR, WITH EVERY SYSTEM!

 
 

What can it do?

dovetail mortise and tenon dovetail mortise and tenon dovetail mortise and tenon dovetail mortise and tenon
dovetail mortise and tenon dovetail mortise and tenon dovetail mortise and tenon dovetail mortise and tenon
 

 

SAFETY COMES FIRST WITH LIGNATOOL:

Safety featuresLIGNATOOL features three very important safety features that impressed us:

1. The Lignatool milling bit is built not with 12, but rather a 20 mm shank, (bigger than 3/4"!), which is exponentially stronger to withstand the rated @24,000 rpm that most routers run at. It fastens straight onto router shaft end. No adapter required for most routers. 

2. Normally, when milling into knotty material, it is possible for kick-back to knock an unsecured router off its path. At worst, you may be injured. If you're lucky, you only damage the bit, the template, or the timber piece you are working on.

This is NOT a problem with the LIGNATOOL. Lignatool LOCKS THE ROUTER SECURELY and SAFELY into a guide plate. The guide plate easily leads the router in any direction around the template until the tenon or mortise is completed.

3. Every Lignatool dovetail kit includes a top-mounted vertical dust deflector, OPTIONAL: Horizontal shield.

 

Components

Systainer
Supplied in a practical Systainer with foam insert.
Except size LT140 and LT180, these are delivered in a cardboard box.
Jigs Jigs made of anodized aluminum with scales in mm divisions and bushings made of stainless steel that can be replaced when worn.
Scales Scales made of black anodized aluminum with bright engraving for high reading contrast, resistant to solvents and mechanical stress.
Milling guide The router is hooked into the safety routing guide with the locking plate. This allows you to work safely and without tiring.
Locking plate
The locking plate is screwed onto the soleplate of the router.
 
Suitable for the following routers:
 
 
Setting Gauge Milling depth is set once, only on the tenon backplate using the setting gauge. The milling cutter diameter, the race diameter, the tenon length and the hole depth can also be measured.
Difference Gauge The required correction of the tenon height for sloping wood connections, such as rafters on a ridge, can be read off on the difference gauge.
Horizontal stop The horizontal stop can be adjusted at an angle of up to +-60°.
Vertical stop The vertical stop can be adjusted at an angle of up to +-60°.
Side stop The lateral position of the tenon template is set at the side stop.
Chip protection
The horizontal chip guard is clipped onto the tenon template from above.
The vertical chip protection is pushed from above into the guide groove of the milling guide on the spigot template.
Clamp fixation For quick fixation of the tenon template on the beam, with a lever clamp.
Simplex stop jaws Straight or sloping millings (as with rafters or a vertical roof window change) can be realized with the Simplex stop jaws.
Cutter Milling cutter with reversible blade and race. It is attached with a double-threaded nut directly into the conical shank of the router. Adapters are available for some routers without a conical shank or with a different tool holder.
Variable tenon lengths As seen at the setting gauge, several tenon depths can be selected, between ranges from 15-28mm, depending on the pitch of the ystem being worked with: (LT45 to LT 180).
Compatible with CNC joinery machines The tenon shape as well as the flank angle of 15 degrees is suitable for most CNC joinery machines.
Routers
Suitable for the following routers:
 

What you can do with Lignatool Dovetail Mortise and Tenon Templates

Dovetail mortise and tenon in detailMake tight dovetail joints without gaps.

  • For visible connections or exterior use
  • Eliminate sqeaks in floor joists.
  • Join hip or valley rafters.
  • Make complicated connections where only steel would normally do.

Make 15 connections / hour

  • Easily produce 15 connections per hour by using LignaTool's smart clamping accessories.

Requires heavy-duty router 2000 Watts or higher

  • We have tested several routers and can give you our recommendations (see below).

Use with almost any cross section of wood

  • Mill cross sections from 2" x 2 ” to 8" x 14” with the same template.

Cut wet timber.

Rout in any direction from any side, left or right.

  • The system permits you to allow for quality and grain direction of the wood for the cleanest tear-free milling.

Repeat clamping quickly with additional side fence

Cut compound angles repeatedly using angle adjustable fence.

  • Movable in 2 directions to 51°, important when cutting rafter/purlins

Adjust fence in infinite increments.

  • Tenon height can be set at any position, which is important for compound angles.

Mill to different depths.

  • Change ball-bearing collar rings to achieve different mill depths, important when joining dimensional lumber. (Ask for more information)

Use reversible, quick-change replaceable blades.

Use anywhere: in the workshop or on site.

Sizes: Five Dovetail Shapes to match timber width, from dimensional lumber to round logs

Regardless which pitch you need for your first job, you can buy the other base plates by themselves later, without buying a whole other kit. The other components of the kit will work with all the base plates.

Note: LT 180 template is of larger overall size.

Size LT045

Bar width 4-12 cm

Beam height 4-24 cm

Tenon angle 1.2°

Download PDF


Size LT060

Bar width 5-16 m

Beam height 5-28 cm

Tenon angle 4°

Download PDF


Size LT080

Bar width 6-18 cm

Beam height 6-32 cm

Tenon angle 8°

Download PDF


Size LT120

Bar width 8-20 cm

Beam height 8-36 cm

Tenon angle 16°

Download PDF


Size LT180

Bar width 10-28 cm

Beam height 10-36 cm

Tenon angle 16°

Download PDF


 

Compare Packages and Components

Regardless of which version you buy, you can always add individual components later as you need them.

Download PDF of this chart

All Accessories Available Separately

Upgrade your Lignatool. In addition to the parts listed and priced in our store below, the following items can be purchased separately. Please contact us directly to order:

Side fenceSide fence for repeatable side positioning - can be mounted on left or right.

Clip on dust shield

Depth setting gauge

Router guide with router base plate

Compatible Heavy-Duty Routers

Lignatool requires a heavy-duty router. We have tested Lignatool with the following routers and have found them compatible. Save $100 when you buy a Scheer router together with the Lignatool Dovetail Mortise and Tenon Templates.

CUSTOMER NOTE:
 
Often we get asked whether their heaviest-duty "XYZ" router make will work with the Lignatool system. We can state categorically it will not. Only if you already own one of the 4 makes we mention in our pages, can you be assured they have the initial power to force through 1” deep material, in one pass. Only the Scheer and Mafell routers have the sustaining power to keep working continually.
 
Therefore if you plan on using the Lignatool system often, it pays to consider the sustainability of the router at 1" cutting depth. The others are "Commercial" duty routers who have the initial power, but do not have the sustaining power.
 
We will include a router plate to match one of these routers (Mafell LO65, Festool 2300, Scheer HM25, Makita 2301). When ordering, please specify the make of your router.  
Makita router RP2301FC
Makita RP2301FC
(Contact your dealer to purchase)

Festool OF 2200
(Contact your dealer to purchase)

 

Some Project Examples:

1. Cutting a compound wood-to-wood connection

2. Cutting joists for a floor system in just 3 days.

This is from a TimberTools customer. With the templates and a heavy-duty router, he fitted floor joists by cutting dovetails with the templates.

He thought it would take him several WEEKS, but finished his multi-story floor system in just 3 DAYS.

Note the "thumbs up" in the last picture.

cutting a tenondovetail joinery rafterscompleted dovetail tenonusing the tenon template

 

3. Examples of work by Lignatool customers.

                                                dovetail mortise and tenon in jack rafter     

 

Products

Green wood bit
Green wood bit
Please call us at 1-416-675-2366 to order.
Reversible knife for router milling bit (10-pack), 8 deg.
Reversible knife for router milling bit (10-pack), 8 deg.
Please call us at 1-416-675-2366 to order.
15° Milling Bits for Lignatool Templates
15° Milling Bits for Lignatool Templates
$ 790.00

Lignatool Complete Kit
Lignatool Complete Kit
$ 5815.00

Lignatool Pro Kit
Lignatool Pro Kit
$ 4915.00

Collar ring with bearing
Collar ring with bearing
$ 97.10
Qty
Lignatool Starter Kit
Lignatool Starter Kit
$ 3740.00

Reversible knife for router milling bit (10-pack), 15 deg.
Reversible knife for router milling bit (10-pack), 15 deg.
$ 179.00
Qty
Gift certificates